How To Set Up Hot Tub
You've decided to take the plunge and become a new Hot Tub! With a footling planning and grooming, installation is an easy chore you can complete quickly.
There are some effectively points hot tub start-timers should be enlightened of. Let's go over it, step past pace.
Preparing for Your Spa
Site Pick
View, privacy and admission are major factors when choosing a site for the spa. Outdoor placement is easier and cheaper than indoor, only both have their advantages.
Before choosing a site outdoors, think virtually the view from inside the tub. Looking at your neighbors junk car collection or utility lines is not going to be very relaxing. Trees and plants are nice, just not too shut to the tub, since they drop leaves and other droppings.
Once yous've narrowed down your placement choices, your final site should accept:
- A smooth, level surface
- Structure to support the weight of the tub, h2o & occupants
- Adequate drainage for rainwater & splash out
- Accessibility to all panels for maintenance or repairs
- Privacy
It may make sense to place the spa indoors if privacy, easy access and shelter from the weather are important. Here's what you lot need for good indoor install:
Spa Foundation
Concrete - Reinforced concrete slabs provide a good base for hot tubs, but here are a few other price saving ideas:
Gravel Base - This is the to the lowest degree expensive option for a foundation. Ensure that the ground is compacted and that rainwater and splashed/drained water will flow away from the tub. Calculation pavers or a walkway to the spa will keep dirt and gravel out.
Decking - Wooden decks look great, especially when yous build the tub into them. If you're placing the tub on a deck or elevated structure, have an engineer or contractor approve the pattern.
Utility Requirements
The spa site needs a drain field nearby. Keep in heed, yous'll bleed upwardly to 500 gallons from the tub every three-four months. While well-nigh plant life tolerates treated hot tub water, avoid delicate plants like roses or vegetables.
Programme for the electrical needs of the spa. Is the spa location within achieve of power?
For safety, all spas must connect to a Ground Fault Excursion Interrupter (GFCI). In case of an electrical short, this vital safety device cuts power in as footling as one/40th of a second.
240 Volt spas run on hard wired GFCI protected circuits. These crave a qualified electrician to run a 240 Volt line out to a GFCI Load Center/Disconnect. The further the spa is from the main breaker box, the more it will toll to wire it.
Wiring a Hot Tub Spa
120 Volt plug and play spas run off standard 15 amp household circuits. These tubs have a GFCI built right into the electrical cord.
Plan ahead: National Electric Lawmaking requires 120 Volt receptacles to be 5' minimum and x' maximum from the tub. You might need an electrician to install a new plug-in closer to the tub. Caution: Never employ extension cords.
Note: Since 120V hot tubs need a dedicated 15 amp circuit, an electrician will usually need to install that line.
Spa Access
For both indoor and outdoor placement, permit admission to all sides of the hot tub. This is important when information technology comes to maintenance and repairs. Parts can exist placed anywhere in the cabinet, then being able to remove all of the panels is crucial.
Install hatches or a crawl space effectually the spa if you plan to surround the tub with a deck. Comfort while working on the hot tub is of import. Give 18" – 24" of space for a full grown adult to access the within of the tub.
Site Admission
Wait at the route from the commitment betoken to the spas last location. Hot tub makers will provide the dimensions of the delivered package if yous ask. Accept a tape measure out and walk the actual path the tub will travel. Make a plan for any trouble spots. Wait out for depression eaves, air conditioner units, narrow gates, stairs, or annihilation that will make maneuvering difficult.
Crane services are an option if you live on a hillside or the desired site is difficult to access. A crane can lift the spa over walls and trouble spots with ease and may price less than you'd await.
Installation & Setup
Delivery
The majority of spas purchased online are delivered curbside. That means the tub volition exist carefully delivered to the end of your driveway. Spas purchased from dealers may be delivered to the final location, but sentinel out for extra charges for this service.
Yous will desire to be present on commitment twenty-four hours to audit the spa for any impairment. With a few helpers on mitt, follow your program and move the tub to its final location.
Positioning the Spa
Moving the hot tub to its final location is piece of cake for 2 to 3 people depending on its size. Since the tub volition make it on a pallet, a pallet jack is an easy tool to employ.
Furniture or pianoforte dollies are other options. These wheeled frames are available at moving companies to rent or purchase.
Sections of lawn or uneven ground are like shooting fish in a barrel to navigate with a smooth runway. Cutting a iv' Ten 8' piece of plywood in half, yielding two 2' X viii' sheets. Movement 1 sheet in front of the other as the spa moves forwards.
Pre-Fill Prep
With the tub placed in its concluding location and the power connected, it's time to begin the startup procedure. Familiarizing yourself with the features and functions of the spa is of import, so read the owner's manual completely before continuing.
- Remove exterior panels
- Hand tighten loose unions at the heater and each pump
- Open up gate valves by pulling the handle upwardly & locking it using the Gate Keeper
- Remove filters from spa filter chamber
- Clean the interior with a pH neutral, not-foaming cleaner
- Rinse the spa beat
- Fill with about 12" of water
- Open the drain valve to release the dirty water
- Close the drain valve
Filling your Spa
Before finally filling your hot tub, take stock of the status of your water source. Apply a PreFresh hose end spa pre-filter if your h2o is from a well, or has other impurities.
Also double check your manual for the recommended fill height, equally it tin vary between spa brands.
Insert the hose into the empty filter chamber and fill the spa.
Ability Up
The spa must exist total of h2o before turning information technology on. Powering on your hot tub without water can damage the heater.
- Turn on the power at the GFCI breaker or plug-in
- Reinstall the filter
- Bank check the pumps by pressing the "Jets" buttons on the keypad
- Look for leaks inside the chiffonier while the pumps are running
- Gear up the heat to your desired temperature
- Replace and secure the cabinet panels
Note: It tin can accept from several hours to a full day for the tub to estrus upwardly.
Remainder & Sanitize
Now that the tub is full and everything checks out, it's time to balance and sanitize the water. Pro Supplies Kits are available if a chemic supplies kit didn't come with the spa.
Learn more about balancing and sanitizing your spa:
ABCs of Water Chemistry
Hot Tub H2o Prep and Maintenance
Of import: The information provided hither is for educational purposes but. It is neither a substitute nor a replacement for data contained in your owner'due south manual. Consult with your local building department, qualified licensed contractor, or structural engineer for structural and electric requirements equally advisable.
Source: https://www.spadepot.com/setup.htm
0 Response to "How To Set Up Hot Tub"
Post a Comment