How To Set Up A Bowflex Xtl

About Bowflex XTL User Manual

Bowflex XTL Power Pro Assembly Instructions

Before you begin, you lot will need a 9/16" wrench, a seven/16" wrench, a 1/2" open end wrench, a crescentvwrench (to concord the commodities while tightening with other), a prophylactic mallet (for step #5) and a phillips headv(+) spiral commuter. Delight follow these assembly instructions carefully. If y'all experience any difficulty,vplease phone call a Bowflex client service representative and ask for aid. one-800-269-3539.

Bowflex XTL Power Pro Table of Content

• Bowflex Power Pro
• Part Reference and Size Guide
• PowerPro Reference Guide
• Assembly Instructions
• Leg Extension Attachment
• Part Reference and Size Guide
• Associates Instructions
• Chest Bar Attachment
• Assembly Instructions
• Lat Pulldown Attachment
• Part Reference and Size Guide
• Associates Instructions
• Squat Zipper
• Associates Instructions
• Do Instructions
• Foot Harness Attachment
• Assembly Instructions
• Boosted Power Rods
• Associates Instructions

Bowflex XTL Power Pro Associates Instructions

Before yous brainstorm, yous will need a ix/sixteen" wrench, a seven/16" wrench, a 1/two" open end wrench, a crescent wrench (to agree the bolt while tightening with other), a rubber mallet (for step #5) and a phillips caput (+) screw driver. Delight follow these associates instructions advisedly. If you lot experience any difficulty, please phone call a Bowflex customer service representative and ask for assist. 1-800-269-3539.

Bowflex Power Pro Parts Reference Guide

Step 1:
Locate the Rear Leg and Seat Rails.

1a.

Take 2 three/8" x 3/4" square head bolts and place them through holes on the Rear Leg Bolt Keeper. Have that assembly and slide it into the Seat Runway channel, starting
on the end closest to the warning label. Make certain to line upwards the terminate of the commodities keeper with the end of the rails. Repeat for the other bolt keeper. In one case you accept both commodities keepers in identify, install the Rear Leg – place four 3/8" washers and tighten a iii/8" nylon locknut on to each of the bolts. Delight use caution when inserting the bolt keeper. Edges may be sharp.

1b.

Next, have ii 3/8" x three/4" square head bolts and slide one into each side of the Seat Rails channel from the opposite end. Locate the Riser Subclass and attach it to the Seat Rails with the two square head bolts. Wait to tighten bolts with a wrench until subsequently Step 1c.

1c.

Now, locate the bolt keeper for the pivot bracket and two 3/eight" ten 3/4" square head bolts. Install the bolts into the bolt keeper. Slide them into the Seat Track Channel making sure the keeper is flush with the end of the Seat Rail. Repeat for the other commodities keeper. Locate the Pivot Bracket and Pulley Frame. Snap the Pivot Bracket between the screw heads on the Caster Frame. Install the rail and then the four bolts at the forepart of the rails slide through the four holes in the pin bracket. Utilize 3/8" washers and 3/viii" nylon lock basics to secure the rail.

IMPORTANT: Place Seat Track then that the end of the rails is affluent with the edge of the Pivot Bracket. Connect the bottom of the Riser Bracket to the standing platform with the 1" Knob. Run across instance 1c.

Readmore and Download Bowflex XTL User Manual on PDF Below

Title	: Bowflex XTL User Manual on PDF Below
Format	: PDF
Pages	: Pages
Language	: English
File Size	: 5 MB

Source: https://www.manualsbooks.com/bowflex/home-gyms/bowflex-xtl-user-manual.html

Share this post